[Daekyung Tech] Clutch Cover Characteristics TesterQuote Contact_ CS@roasexpo.comThis is a dedicated testing machine for clutch cover characteristics for automobiles.Delivered to SECO.It is a device that obtains results by measuring the operation area and characteristics by applying a load to the release lever and clutch disk.CAPACITY : CLAMPING LO..

[Daekyung Tech] Ball Joint Gap TesterQuote Contact_CS@roasexpo.comAfter checking the gap characteristics of the ball joint,a durability test is performed and the changed characteristics are judged by comparing before and after the test.CAPACITY : ±30 kNRESOLUTION : WITHIN ±0.5%FREQUENCY : 40HzCONTROL : P.C CONTROLSAMPLE : IBJ, OBJMODE : L..

[Daekyung Tech] Ball Joint Durability TesterQuote Contact_CS@roasexpo.comDTE-179M- This device is a dust cover durability tester.-It is an equipment for the durability tester of the dust cover, and it uses a computer system to Test samples under environmental conditions using a hydraulic system and chamber controlled by servo valve It was..

[Daekyung Tech] Ball Joint Durability TesterQuote Contact_CS@roasexpo.comThis equipment performs long-term durability tests on vehicle ball joints at specified angles at room temperature, high temperature, and low temperature.After the test, the condition of the ball joint and the condition of the rubber cover are analyzed.At this time, the test ca..

[Daekyung Tech] Seat frame strength testerQuote Contact_ CS@roasexpo.comIt is a testing machine that tests the frame rigidity of automobile seats.Secure the seat frame to the T-slot bed at the back and pull it with a chain to test its strength.In consideration of the load transfer during an automobile accident or sudden braking, the test is carried..

[Daekyung Tech] Clutch release lever durability testerQuote Contact_cs@roasexpo.comIt is a device that obtains results by measuring the operation and characteristics of the release lever by repeating the durability test.It is for clutch tester of large vehicles.It was delivered to the research institute attached to the automobile.CAPACITY : (0 ~ 15..

[Daekyung Tech] Handle wear testerQuote Contact@CS@roasexpo.comIt is manufactured according to the MS 625-04 standard and is suitable for the abrasion test of leather handles.The cloth is sprayed with a liquid with a composition similar to human sweat and subjected to a specific load and repeated test.The durability of the handle material is tested..

[Daekyung Tech] Zeolite TesterQuote Contact@CS@roasexpo.comThis equipment is used to test the paintwork of automobiles.When a car runs and collides with small stones, it tests whether the painted surface is damaged by reproducing a situation similar to the actual condition.Small pieces of stone that meet international standards are blown away at hi..

[Daekyung Tech] Hose Clamp TesterQuote Contact@CS@roasexpo.comThis equipment tests the strength of hose clamps for vehicles.Measure the force by pulling the hose clamp in three directions, equally spaced at 120 degrees.It is a device for measuring the clamping force of "SUS wire clamp" for automobile hoses,and it is a device to measure the force us..

[Daekyung Tech] Bicycle durability testerQuote Contact_CS@roasexpo.comThis is a bicycle parts durability tester supplied to Samchully Bicycle.It consists of a device that tests the durability of the front fork and rear shock,which are the main parts of a bicycle, and a device that runs under conditions similar to actual road driving after installin..

[Daekyung Tech] Weather strip Endurance testerQuote Contact_CS@roasexpo.comIt is an equipment manufactured for the purpose of durability test,research and development by repeatedly opening and closing windows while periodically supplying temperature, humidity, dust and water to the exterior dust strip of the vehicle.LOADING : AIR CYLINDERMODE : CYC..

[Daekyung Tech] Seat belt spring testerQuote Contact_CS@roasexpo.comThis equipment tests the durability of the spring used in seat belts.Durability is verified by repeatedly performing millions of tests in clockwise and counterclockwise directions.Depending on the number of samples, various sizes can be produced.LOADING : SERVO MOTORMODE : CW &..

[Daekyung Tech] Spring steel deformation simulation testerQuote Contact_CS@roasexpo.comAfter performing a characteristic test of the spring for automobile seat belt by rotating it forward and backward as much as a prescribed angle,it is checked to determine the deformation or characteristics of the material.CAPACITY : 50 N.mLOADING : SERVO MOTORMOD..

[Daekyung Tech] Transmission properties testerQuote Contact@CS@roasexpo.comIt is a device that applies rotational force to the input stage of the transmission,and measures the torsion applied to the output stage 4 axes to obtain the result.CAPACITY : 50N.mRESOLUTION : WITHIN ± 1%CONTROL : P.C CONTROLMODE : TORQUE VS AVGLESAMPLE : STEERING SHAF..

[Daekyung Tech] Torsion testerQuote Contact_ cs@roasexpo.comIt can test and measure the breaking torque, axial force, angle,and forward/reverse torque force of small bolts. It consists of an X-Y table, a balance weight, and a pressure weight.CAPACITY : 100N.mACCURACY : WITHIN ± 0.8%RESOLUTION : 1/200,000 F.S.CAMPLE FIX : X-Y TABLECENTERING : ..

[Daekyung Tech] Torsional testing machineQuote Contact_ cs@roasexpo.comIt is manufactured for the purpose of research/development by measuring the rotational force attenuation when the complex structure metal round material is rotated at high speed and the rotational force is removed or the deformation caused by the centrifugal force.PRM : ~ 20,000..

[Daekyung Tech] Hot torsion testing machineQuote Contact_ cs@roasexpo.comIt is manufactured for the purpose of researching and developing the deformation and, characteristics of materials by rapidly heating various round and wire rods to high temperature and rotating them at high speed.CAPACITY : 200 kN.mACCURACY : WITHIN ± 1%TABLE : X AXIS SL..

[Daekyung Tech] Rotational bending testerQuote Contact_CS@roasexpo.comIt is manufactured to perform 4-point bending tests of various wire rods and, round materials, and environmental devices can be attached on demand.CAPACITY : 100 N.mCONTROL : SEMI-AUTO, MANUALSAMPLE : Ø 10 mmSPEED : (1,500 ~ 3,000) rpmLOADING : MOTOR WEIGHT : 100 kgCHUC..

[Daekyung Tech] Clutch disc torsion characteristic testerQuote Contact@CS@roasexpo.com[Summary] This is a precision equipment for total inspection to obtain the torsional torque and angle of the clutch disk for automobiles. It is driven by AC Servo Motor, and all control is done by computer, and it is a device that analyzes data by program.Tourque:..

[Daekyung Tech] Bolt torsional testing machineQuote Contact_ CS@roasexpo.comIt is a tester that measures the torque and axial force of high-tensile bolts.CAPACITY : TORQUE 1kN.mTENSILE 200 kNACCURACY : WITHIN ± 1%BOLT SIZE : M(5 ~ 6)CONTROL : P.C CONTROLSAMPLE : BOLTOUTPUT : TORQUE, TENSILE, ANGLELOADING : SERVO MOTORSPEED : (1 ~ 5) rpm, (1 ~ ..

[Daekyung Tech] Bottle cap torque testerQuote Contact_cs@roasexpo.comThis is a tester that measures the torque generated when the bottle cap is opened.Data is displayed in units such as Nm, Ibf.in, etc., and test results are automatically saved in the desired folder.Up to 2 liter bottles can be tested, and samples from 12 to 24 can be adjusted acco..

[Daekyung Tech] DryerQuote Contact_ cs@roasexpo.comIt is designed and manufactured for the purpose of testing the shrinkage and aging state of specimens by heating rubber, plastic,and electric wires at high temperature.TEMP : (RT ~ 250) ℃INNER SIZE : (500 X 500 X 500) mmINNER MATERIAL : STS 304OUTER MATERIAL : SS41 COATINGCONTROL : P.I.K CONTR..

[Daekyung Tech] Salt spray chamberQuote Contact_ cs@roasexpo.comIt is manufactured to observe corrosion resistance test by generating corrosion of metal.The internal size varies depending on the option, and it is manufactured to enable complex corrosion.This is a testing machine that mainly sprays salt water on a metal sample to check the degree of..

[Daekyung Tech] Thermo-hygrostatQuote Contact_cs@roasexpo.comThe purpose is to observe the deformation of the product or sample by gradually changing the temperature and, humidity or applying a continuous environment, and it can be manufactured according to the order.INNER SIZE : (500 X 500 X 600) mmTEST TEMP : (-40 ~ 150) ℃HUMIDITY : (30 ~ 98..

[Daekyung Tech] Flame retardant tester (horizontal type)Quote inquiry_ CS@roasexpo.comThis tester is designed and manufactured in accordance with KS and UL standards for the purpose of inspecting the flame retardancy and, combustibility of specimens by controlling and applying the prescribed flame to specimens such as various wires, plastics, and f..