[Daekyung Tech] Real load torque calibrator 100 NMQuote Contact_CS@roasexpo.comIt is a device for correcting torque.The maximum torque is 100 NM, automatically sets the weight, and is designed to measure clockwise/counterclockwise torque.All courses are conducted through Daekyung Tech's dedicated program.The above products are being supplied and us..

[Daekyung Tech] Real load torque calibrator 100 NMQuote Contact_CS@roasexpo.comIt is a device for correcting torque.The maximum torque is 100 NM, automatically sets the weight, and is designed to measure clockwise/counterclockwise torque.All courses are conducted through Daekyung Tech's dedicated program.The above products are being supplied and us..

[Daekyung Tech] Hydraulic force calibratorQuote Contact_CS@roasexpo.comThis equipment is used for calibration and testing of electric force measuring instruments (load cells), and is used to correct the difference between the high-precision master cell,  and the device to be calibrated or to issue a report by the calibration procedure.It is a ..

[Daekyung Tech] Real load force calibrator 10kNQuote Contact_CS@roasexpo.comIt is a standard calibration device that is used for calibration and testing of electric force measuring instruments (load cells), and is calibrated by accurate weight including local gravitational acceleration.It is an instrument for calibrating force measuring instruments..

[Daekyung Tech] Hydraulic force calibratorQuote Contact_CS@roasexpo.comIt is a hydraulic force calibrator with a capacity of 5 MN (approximately 500 tons).It has an uncertainty of 0.05% and is equipped with a two-stage master cell of 5 MN + 2 MN.Tensile/compression bidirectional measurement is possible.It was delivered to VMI in Hanoi, Vietnam, whi..

[Daekyung Tech] Push-pull gauge calibratorQuote Contact_CS@roasexpo.comThis equipment is used for calibration and testing of electric or dial-type push-pull gauges.CAPACITY :  ( 2 ~ 2,000) NCONTROL : MANUALLOADING : DEAD WEIGHTDEAD WEIGHT : STEEL COATING, F2 GRADEMODE : TENSILE , COMPRESSION..

[Daekyung Tech] Hydraulic force calibrator 1 MNQuote Contact_CS@roasexpo.comThis equipment is used for calibration and testing of electric force measuring instruments (load cells), and is used to correct the difference between the high-precision master cell,  and the device to be calibrated or to issue a report by the calibration procedure.It ..

[Daekyung Tech] Hydraulic force calibrator 20kNQuote Contact_CS@roasexpo.comThis equipment is used for calibration and testing of electric force measuring instruments (load cells), and is used to correct the difference between the high-precision master cell,  and the device to be calibrated or to issue a report by the calibration procedure.It ..

[Daekyung Tech] Force cailbrator by dead weightQuote Contact_CS@roasexpo.comIt is a standard calibration device that is used for calibration and testing of electric force measuring instruments (load cells), and is calibrated by accurate weight including local gravitational acceleration.CAPACITY :  200 N ~ 20kNBMC : WITHIN 0.005 %LOADING : AIR ..

[Daekyung Tech] Hydraulic force calibrator 50kNQuote Contact_CS@roasexpo.comThis equipment is used for calibration and testing of electric force measuring instruments (load cells), and is used to correct the difference between the high-precision master cell,  and the device to be calibrated or to issue a report by the calibration procedure.It ..

[Daekyung Tech] Tire durability testerQuote Contact_ CS@roasexpo.comThis is a testing machine designed to test the durability of tires.The wear resistance of tires is tested by creating an environment similar to real driving conditions.It is an equipment that obtains results by measuring the characteristics of a tire by rotating a vehicle tire unde..

[Daekyung Tech] Clutch Cover Characteristics TesterQuote Contact_ CS@roasexpo.comThis is a dedicated testing machine for clutch cover characteristics for automobiles.Delivered to SECO.It is a device that obtains results by measuring the operation area and characteristics by applying a load to the release lever and clutch disk.CAPACITY : CLAMPING LO..

[Daekyung Tech] Ball Joint Gap TesterQuote Contact_CS@roasexpo.comAfter checking the gap characteristics of the ball joint,a durability test is performed and the changed characteristics are judged by comparing before and after the test.CAPACITY : ±30 kNRESOLUTION : WITHIN ±0.5%FREQUENCY : 40HzCONTROL : P.C CONTROLSAMPLE : IBJ, OBJMODE : L..

[Daekyung Tech] Ball Joint Durability TesterQuote Contact_CS@roasexpo.comDTE-179M- This device is a dust cover durability tester.-It is an equipment for the durability tester of the dust cover, and it uses a computer system to Test samples under environmental conditions using a hydraulic system and chamber controlled by servo valve It was..

[Daekyung Tech] Ball Joint Durability TesterQuote Contact_CS@roasexpo.comThis equipment performs long-term durability tests on vehicle ball joints at specified angles at room temperature, high temperature, and low temperature.After the test, the condition of the ball joint and the condition of the rubber cover are analyzed.At this time, the test ca..

[Daekyung Tech] Seat frame strength testerQuote Contact_ CS@roasexpo.comIt is a testing machine that tests the frame rigidity of automobile seats.Secure the seat frame to the T-slot bed at the back and pull it with a chain to test its strength.In consideration of the load transfer during an automobile accident or sudden braking, the test is carried..

[Daekyung Tech] Clutch release lever durability testerQuote Contact_cs@roasexpo.comIt is a device that obtains results by measuring the operation and characteristics of the release lever by repeating the durability test.It is for clutch tester of large vehicles.It was delivered to the research institute attached to the automobile.CAPACITY : (0 ~ 15..

[Daekyung Tech] Handle wear testerQuote Contact@CS@roasexpo.comIt is manufactured according to the MS 625-04 standard and is suitable for the abrasion test of leather handles.The cloth is sprayed with a liquid with a composition similar to human sweat and subjected to a specific load and repeated test.The durability of the handle material is tested..

[Daekyung Tech] Zeolite TesterQuote Contact@CS@roasexpo.comThis equipment is used to test the paintwork of automobiles.When a car runs and collides with small stones, it tests whether the painted surface is damaged by reproducing a situation similar to the actual condition.Small pieces of stone that meet international standards are blown away at hi..

[Daekyung Tech] Hose Clamp TesterQuote Contact@CS@roasexpo.comThis equipment tests the strength of hose clamps for vehicles.Measure the force by pulling the hose clamp in three directions, equally spaced at 120 degrees.It is a device for measuring the clamping force of "SUS wire clamp" for automobile hoses,and it is a device to measure the force us..

[Daekyung Tech] Bicycle durability testerQuote Contact_CS@roasexpo.comThis is a bicycle parts durability tester supplied to Samchully Bicycle.It consists of a device that tests the durability of the front fork and rear shock,which are the main parts of a bicycle, and a device that runs under conditions similar to actual road driving after installin..

[Daekyung Tech] Weather strip Endurance testerQuote Contact_CS@roasexpo.comIt is an equipment manufactured for the purpose of durability test,research and development by repeatedly opening and closing windows while periodically supplying temperature, humidity, dust and water to the exterior dust strip of the vehicle.LOADING : AIR CYLINDERMODE : CYC..

[Daekyung Tech] Seat belt spring testerQuote Contact_CS@roasexpo.comThis equipment tests the durability of the spring used in seat belts.Durability is verified by repeatedly performing millions of tests in clockwise and counterclockwise directions.Depending on the number of samples, various sizes can be produced.LOADING : SERVO MOTORMODE : CW &..

[Daekyung Tech] Spring steel deformation simulation testerQuote Contact_CS@roasexpo.comAfter performing a characteristic test of the spring for automobile seat belt by rotating it forward and backward as much as a prescribed angle,it is checked to determine the deformation or characteristics of the material.CAPACITY : 50 N.mLOADING : SERVO MOTORMOD..

[Daekyung Tech] Transmission properties testerQuote Contact@CS@roasexpo.comIt is a device that applies rotational force to the input stage of the transmission,and measures the torsion applied to the output stage 4 axes to obtain the result.CAPACITY : 50N.mRESOLUTION : WITHIN ± 1%CONTROL : P.C CONTROLMODE : TORQUE VS AVGLESAMPLE : STEERING SHAF..